Others in this category
  • Berger External Filler is a ready-to-use  filler based on special nano emulsion of 100% pure acrylic binder for interior and exterior
  • Berger Luxatile Epoxy Spray Compound Low Sheen Texture Coating for ecterior walls
  • Berger Weathercoat Acrylic Spray Co-polymer Wall Compound

External Filler

A ready-to-use graded exterior filler based on special nano emulsion. It can be applied directly to fair-faced surfaces to smoothen surface irregularities.

External Filler is a ready-to-use exterior graded filler based on special nano emulsion of 100% pure acrylic binder. It can be applied directly to most fair-face surfaces such as concrete, plasterboard walls and ceilings, brick or block work in exterior settings. When needed, it can be used for interiors as well. Once External Filler has been applied, it can be overcoated with a range of paint finishes.

Features

See all
Based on nano emulsionExcellent hiding powerAdheres to most surfaces
Finishes -Matt

Surface preparation Ensure that the surface is clean, dry and free of all contaminants. Remove laitance (accumulation of particles on fresh concrete), if any, with a wire brush or sweep blast. Treat any fungal growth with Fungicidal Solution.

Application procedure Stir the contents thoroughly with a broad flat stirrer, before and during use, using an upward lifting action. Apply with a trowel or putty knife to fill surface irregularities, indentations and undulations to produce a smooth and levelled surface before painting.

Tools you will need

Trowel
Putty Knife

Available Packs

Berger External Filler is a ready-to-use  filler based on special nano emulsion of 100% pure acrylic binder for interior and exterior
3.6 Ltr

Berger External Filler is a ready-to-use  filler based on special nano emulsion of 100% pure acrylic binder for interior and exterior
18.9 Ltr

1 Coat
2.5 m2/Ltr**

Coverage

On well-prepared surfaces, as per the painting system recommended. Please refer to the Product Data Sheet for surface preparation and method of application.

** Actual coverage may vary from the quoted coverage due to factors such as method and condition of application, surface roughness, and porosity.

Volume Solids


60% ± 2%

Solve Potential Paint Problems

1There are bumps at regular intervals along my wall.

The bumps or little projections are called undulations, and are usually caused by little cracks and splits that appear in the surface as your building “settles”. These imperfections are usually visible near corners, around windows and doors, or at joints of the wall.

What are the possible causes?

  • This is caused due to imperfect plastering
  • The cracks develop over time as your building settles or suffers damage

How can I fix the problem?

  • If the undulations are minor, fill and level with stucco or putty. For major undulations on the wall surface, plaster work will be needed.
  • Sand to make the surface uniform.
  • Apply primer, filler and suitable top coat.

We recommend you use this painting system to avoid this problem the next time around:

  • Alkali Resistant Primer
  • Value Stucco
  • Royale Luxury Matt Emulsion
  • Value Stucco
  • Weathercoat Primer
  • External Filler
  • Weathercoat Ultra - Silk
  • Weathercoat Primer
  • External Filler
  • Weathercoat Ultra - Matt
  • Weathercoat Primer
  • External Filler
  • Weathercoat Flex Smooth
  • Weathercoat Primer
  • External Filler
  • Weathercoat Ultra - Silk
  • Weathercoat Primer
  • External Filler
  • Weathercoat Ultra - Matt
  • Weathercoat Primer
  • External Filler
  • Get Inspiration

  • Make Your Plan

    Let us design a project plan to suit your needs.

  • Colour Guides

dealer locator

Locate
Note:-
The shades displayed on this website are indicative only and may vary from the actual colours due to variance in monitor calibration and resolution as well as screen settings.
Thank you for subscribing!